AUDIO INNOVATE AEM-100i DJ MIXER

Introducing the AEM-100i – Where synth, analog filter warmth and crossfader precision come together in one great package.

Create your own signature sound. Make precision timed cuts on the crossfader with a top quality Pro X Fade. Never worry about running out of emergency inputs. We made it all happen with the AEM-100i.

Fitted as standard in the AEM-100i is the Pro X Fade from Eclectic Breaks which they launched at Plasa 2005, to rid the DJ industry of its Achilles heel and create a virtually unbreakable crossfader.

The Audio innovate AEM-100i is a unique concept 2 channel mixer for working and performing DJs. Forget more of the same, we put an analog synth and effects in a DJ friendly format.

-> Built in Oscillator
-> Analog filters and effects on both channels
->Wet / dry and cueing for building your own synth sounds / effects
-> Pro X Fade with 1 year warranty
-> Crossfader and Line fader reverse & slope adjust
-> Fader Start from the crossfader, line faders
-> PFL and AFL sound meters
-> 4 inputs per channel with Aux both front and back
-> 2 Mic inputs
-> XLR balanced outputs
-> VCA fader control
-> New ergonomic knobs and faceplate

TECHNICAL SPECIFICATIONS:
Inputs:
Line/Aux: 10kΩ input impedance, 5.6mV rms sensitivity for 1.0V output
Mic: 10kΩ input impedance, 1mV rms sensitivity for 1.0V output
Phono: 47kΩ input impedance, 0.9mV rms sensitivity @ 1kHz for 1.0V output
Outputs:
Master: 8.6V rms Booth: 8.6V rms
Record: 1.0V rms Headphone Amp: .5 watts / 47Ω, THD < 0.1%
Equalizer:
3-band Stereo Equalizer per channel, -30dB cut / +10dB boost
Signal to noise ratio
Line: 92dB (JIS-A) Aux: 92dB (JIS-A)
Mic: 87dB (JIS-A) Phono: 83dB (JIS-A)
Frequency Response
Line: 20Hz~20kHz ±1dB Aux: 20Hz~20kHz ±1dB
Mic: 20Hz~15kHz ±1dB Phono: RIAA ±0.5dB
Talkover attenuation: Maximum –19dB, minimum –16dB attenuation of main audio
Power consumption: 18 Watts typical, 22 Watts with full headphone output
Dimensions: 10” wide * 14” deep * 4.2” high
Weight: 6.0kg
Life rating:
Crossfader: >4,000,000 cycles CH1, CH2 Line faders: >100,000 cycles
Misc. faders: >100,000 cycles
Effect circuitry:
Noise, Oscilattor: 0 to 3dB max level, oscillator has variable frequency square wave.
Stutter: variable on/off from a few 1/10ths of a second transforms to high pitched ringing.
Digitize: variable frequency sample/hold circuit.
Phaser: dual phaser with variable cutoff.
Band Pass, Band Reject filters: 4-pole sweepable butterworth filters.
Fader/Crossfader section circuitry:
Minimum slope has cut-in of 1mm or less at the lowest audio position.
Average slope uses 0.2dB typical fader resolution
Maximum slope has cut-in of 1mm or less at the highest audio position.
Maximum delay on VCA fader controls = 1.64msec.
***VCA circuit has no delay in the audio path, delay is for the audio control only.

Thanks for all of your constructive feedback on the AEM-100. Based on your suggestions, we created a more scratch friendly AEM-100i.

The first thing you’ll notice is the color coding. With all of the various sections it’s helpful to be able to look at the mixer and figure out what section does what.

So what happened to the Fader Cuts? Many of you thought it was too much and got in the way of scratching. We still have them on the original AEM-100 but here we figured give you a clean faceplate on the AEM-100i. Getting rid of the Fader Cuts also allowed us to put back the upfader curves and reverse switches.

A good mixer should feel as good as it sounds and functions. So we replaced all of the knobs with color coded rubber knobs. If you get a chance to work with the mixer, you’ll notice that having these knobs makes it easier to work the mixer, especially in the effects section.

http://www.djdeals.com/audioinnovateAEM100I.htm