DBX DriveRack 260 Equalizer Sound Processor
There is a reason that Tour Sound Professionals and discriminating Audio Contractors choose dbx® DriveRack® products for their high-end tours and installs. The DriveRack products provide the tools that ensure that the system sounds its very best. With the introduction of the new 260, the heritage of unrivaled system/loudspeaker control continues.
The 260 capitalizes on the road tested and contractor approved nature of the other products in the DriveRack line. The 260 provides full bandpass and crossover configurations as well as independent output processing and a full time RTA for live sound applications. Contractors will appreciate its control inputs for wall-panel logic control and the patent-pending Advanced Feedback Suppression (AFST).
The DriveRack 260 continues the legacy of DriveRack series, which has been created by the company that has been redefining the standard of signal processing for more than 30 years. The DriveRack 260 was designed with the purpose and vision of providing state-of-the-art signal processing, while utilizing a simple and intuitive user interface. This goal has been achieved by offering two independent channels of processing power with a linkable 28-Band Graphic Equalizer, industry-standard dbx stereo compressor module, feedback eliminator and the 120A Subharmonic Synthesizer on the input, with a six channel output system that includes parametric EQs, PeakStopPlus® limiters (to provide protection against speaker blowouts) and alignment delay. These features combined with the Wizard setup system and complete DriveWareT GUI control represent a methodical design that is guaranteed to deliver optimal, all-inclusive processing in a completely scalable system.
The 260 capitalizes on the road tested and contractor approved nature of the other products in the DriveRack line while adding some new features. The 2 in 6 out 260 offers full bandpass and crossover configurations as well as an independent output processing and a full time RTA for Live Sound applications. Contractors will appreciate its control inputs for wall panel zone control and the Advanced Feedback Suppression (AFS). The 260 also offers an impressive list of features including: Auto Gain control (AGC), Auto EQ and JBL Speaker and Crown Power Amp Tunings with Setup Wizard, and a host of other features and the DriveRack 260 partially sets its self up. All dbx DriveRack units are designed to be the only signal processors necessary between the mixer and the amplifiers.
Features
- Feedback Elimination
- 2.7 Seconds of Alignment and Zone Delay
- RS-232 PC GUI control
- Classic dbx Compression and Limiting
- Graphic and Parametric EQ
- Auto-EQ Function
- Full Bandpass, Crossover, and Routing Configurations
- Auto Gain Control
- Pink Noise Generator and fulltime RTA
- Setup Wizard with JBL speaker and Crown Power Amplifier Tunings
- Security Lockout
- Wall Panel Control Inputs
Inputs
Number of Inputs:
(2) Line inputs. (1) RTA Mic input
Connectors:
(2) Female XLR line inputs. XLR RTA Mic input
Type:
Electronically balanced/RF filtered
Impedance:
>40k ohm
Maximum Input Level:
+34dBu with input jumpers in +30 position
CMRR:
>45 dB
RTA Mic Phantom Voltage:
+15 VDC
RTA Mic ETN:
<-110 dBu, 22 Hz - 22 kHz, 150 ohm
Analog OutputsNumber of Outputs:
6
Connectors:
Male XLR
Type:
Electronically balanced, RF filtered
Impedance:
120ohm
Max Output Level:
+22dBu
A/D PerformanceType:
dbx Type IV™ Conversion System
Dynamic Range line:
>114 dB A-weighted, >112 dB unweighted
Type IV™ dynamic
range:
>119 dB, A-weighted, 22kHz BW
>117 dB, A-weighted, 22kHz BW
Sample Rate:
48kHz
D/A PerformanceDynamic Range:
112 dB A-unweighted, 110 dB unweighted
System PerformanceDynamic Range :
110 dB unweighted, >107 dB weighted
THD + Noise:
0.002% typical at +4 dBu, 1 kHz, 0 dB input gain
Frequency Response:
20 Hz - 20 kHz, +/-0.5 dB
Interchannel Crosstalk:
>110 dB, 120 dB typical
Crosstalk input-output:
>100 dB
SHIPPING INFO: 23X12X4 10 LBS
Warranty Policy:
Should you have a manufacturing defect in your product within 30 days of your order date, simply reply to your original email receipt with an exact description of the problem; We will provide instructions for you to send back the defective product (at your expense) and we will ship you a brand new replacement product (at our expense). Should you have a defect in your product after 30 days from your order date, but before the 1 year warranty expires, simply reply to your original email receipt with an exact description of the problem; We will provide instructions for you to send back the product (at your expense), and will have the product repaired by the manufacturer and returned to you (at our expense).
RELATED ITEMS |
