STANTON A.1800 AMPLIFIER 1800 WATTS
Stanton proudly announces the introduction of the new A Series power amplifiers. Available in three models-the A.900, A.1800, and A.2800-these rugged, 2U rackmountable, workhorses feature state-of-the-art designs that include a highly efficient tunnel cooling system to ensure reliable, cool running operation, 21-position detent level control knobs for easily repeatable settings, signal and clip indicators for convenient monitoring of the amplifier's status, and the right connectors for integration into most any environment.
- Stanton A-Series High Performance Professional Power Amplifiers
- Flow-Through Cooling Design Prevents Overheating
- Speakon NL-4 Locking Output Connectors and Binding Posts
- Balanced XLR and TRS Input Connectors
- Front Panel LED Displays Indicate Power, Clip, Protect and Signal Status
- Detented 21-Position Input Level Control Knobs
- Defeatable Limiter and High Pass Filter Per Channel
The A.1800, a member of the Stanton A series professional amplifier line, brings the power up a few notches from the already strong A.900... bringing musicians to an entirely new level of audio precision.
- Power protection circuitry protects against thermal overload, short circuits, DC voltage, subsonic frequencies and current overdriving
- Independent limiters reduce distortion due to clipping
- Low-Frequency Filters Remove Rumble and Subsonic Frequencies
- Highly efficient tunnel cooling design system maintains low operating temperatures under extreme load conditions
- 21-Position Detent Level Control Knobs with Signal and Clip Indicators Allow Signal to be Perfectly Set to Avoid Clipping
- Speakon® NL-4 locking output connectors and binding posts
- Balanced XLR and TRS input connectors
| Description | Measurement |
| Rated Power: Stereo Both Channels 8 ohms 4 ohms 2 ohms |
400 W 600 W 900 W |
| Rated Power: Bridged Mono 8 ohms 4 ohms |
1200 W 1800 W |
| Signal to Noise Ratio (20 Hz ~ 20k Hz) | 102 dB |
| Distortion (SMPTE-IM) | 0.01% |
| Input Sensitivity @8 ohms | 4dBu |
| Voltage Gain | 33dB |
| Output Circuitry | AB |
| Current Consumption - 120Vac/240Vac @ 1/8 power @ 4ohms @ 1/3 power @ 4ohms @ ratedpower @ 4ohms |
7.2A/3.5A 12A/6A 19.5A/9.5A |
| Distortion | 0.01% |
| 20 Hz-20k Hz Half Power | 0.01% |
| 1k Hz Rated Power | 0.1% |
| Frequency Response | 0/0.5dB ; 20Hz-20kHz, 0/-3dB ; 5Hz-60KHz |
| Dampening Factor (400 Hz) | 280 |
| Input Impedance | 15Kohm Unbalanced, 30Kohm Balanced |
| Input Clipping | 22dBu (10Vrms) |
| Cooling | Continuiusly variable speed, Front to rear |
| Connectors (each) | |
| Input | Advanced balanced combo (XLR and 1/4" TRS common use) |
| Output | 5-way binding post and Speakon® |
| Control | |
| Front | AC power switch, Channel 1 and 2 volume |
| Rear | HPF switch, Limiter switch, Mode selector switch |
| Indicators | Active(blue), Protection(red), Clip(red), Signal(green & yellow) |
| Protection | Short circuit, Thermal, Current limit, DC offset, Current inrush, RF protection, Turn on/Turn off muting |
| Power requirements | 100, 120/240Vac, 50/60 |
| Dimensions (W x H x D) | 19"(482mm) x 3.5"(88mm) x 16.5"(420mm) |
| Net Weight | 40 lbs (18 kg) |
STANTON WARRANTY INFORMATION:
To initiate a warranty repair, you must contact Stanton directly at www.stantondj.com
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your purchase of such merchandise. In no event will Stanton be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of merchantability or fitness for a particular purpose.
Please register your product online at www.stantondj.com or mail your completed warranty card to:
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.
To request a Return Authorization/Repair:
Email: returns @ stantongroup.ws
Fax: 954.316.1590
